TECHNICAL INFORMATION

• The Series 6000 Polymer Feeder provides the high energy needed to effectively activate all liquid polymers.

• The polymer metering pump is a diaphragm pump.  It is available with manual or external control.  The externally controlled pump can accept a 4-20 mA or a pulse signal.

• The dilution water can be clean or filtered process water.

• A low water flow switch is standard on all EXCELL Feeders.  It stops the metering pump whenever the water flow drops below minimum.  The pump automatically restarts when adequate water flow resumes.

• The sight tube is self-cleaning.  The flow of the solution leaving the activating apparatus causes the patented cleaning assembly to operate continuously.  The sight tube allows the operator to see how the feeder is operating.

• The external injection valve is accessible without disturbing the activating apparatus.

• Motor-less activation injects the polymer into the water stream and immediately makes the solution flow through a low pressure, high energy polymer activation nozzle.  The nozzle self compensates for solution flow fluctuations.  This assures that the polymer activation energy level remains adequate as the solution flow changes.

• It's designed to be maintenance free.  All components are modular and easy to access.  There are no parts to wear out and no mixer motors to burn out.                                                            

• A water strainer is standard with each mixer.  The strainer collects debris that may clog the flowmeter or other components.

• A pump calibration cylinder is standard with each mixer.  The cylinder is prepiped with isolation valves to allow checking the metering pump flow rate.

• All components are corrosion resistant.  The mixer support frame is made welded stainless steel.  

   

         

   

STANDARD FEATURES

• Polymer feed capacities of 0.1 to 240 GPD (0.02 to 38 l/h).

• Dilution water capacities of 20 to 1200 GPH (75 to 4500 l/h).

• Easily accessed injection valve.

• Motorless mixing system.  

  A high energy nozzle (Patented) activates the polymer.  

  The nozzle self-compensates for changes in water flow.

• Self cleaning sight glass (Patented).

• Dilution water pressure range capacity of 20 to 100 psi (1.4 to 6.8 bar).

• Polymer pump stops when dilution water flow drops below minimum.

• Prepiped metering pump calibration cylinder system.

• All components are easily accessed.

• Water strainer.

• A drain valve allows complete flushing of the feeder.

• Compact, most units are 15"W x 15"H x 21"D (38 cm x 38 cm x 53 cm).

• Lightweight, most units weigh less than 50 lbs (23 kg).

• Electrical service: 120/240 VAC; 50/60 Hz; less than 300 watts.

• Most units are available for FREE 30 DAY TRIAL (USA only). 

   

  SERIES 6000 STANDARD MODELS

  MODEL NUMBER	POLYMER FLOW GPD (L/H)	WATER FLOW GPH (L/H)
  6000-X	Metering Pump by others	As Required
  6010A-X	0.1 to 10 GPD (0.02 to 1.6 L/H)	10 to 60 GPH (40 to 230 L/H)
  6024A-X	0.6 to 24 GPD (0.1 to 3.8 L/H)	20 to 150 GPH (75 to 570 L/H)
  6010A2-X	0.1 to 10 GPD (0.02 to 1.6 L/H)	10 to 120 GPH (40 to 460 L/H)
  6024A2-X	0.6 to 24 GPD (0.1 to 3.8 L/H)	20 to 300 GPH (75 to 1140 L/H)
  6010-X	0.1 to 10 GPD (0.02 to 1.6 L/H)	20 to 150 GPH (75 to 570 L/H)
  6024-X	0.6 to 24 GPD (0.1 to 3.8 L/H)	30 to 300 GPH (115 to 1140 L/H)
  6048-X	1.2 to 48 GPD (0.2 to 7.6 L/H)	30 to 300 GPH (115 to 1140 L/H)
  6060-K	1.5 to 60 GPD (0.24 to 9.4 L/H)	60 to 600 GPH (230 to 2270 L/H)
  6096-T	2.4 to 96 GPD (0.4 to 15 L/H)	90 to 1200 GPH (340 to 4500 L/H)
  6108-T	3.0 to 108 GPD (0.5 to 17 L/H)	90 to 1200 GPH (340 to 4500 L/H)
  6192-T	4.0 to 192 GPD (0.6 to 30 L/H)	90 to 1200 GPH (340 to 4500 L/H)
  6240-T	4.0 to 240 GPD (0.6 to 38 L/H)	90 to 1200 GPH (340 to 4500 L/H)

        The above models, except the 6048, 6108, and 6192 are rated for 100 psig (6.8 bar).  

        Models 6048, 6018, and 6192 are rated for 50 psig (3.4 bar).

        Models 6010A and 6024A have a one gallon capacity blending-aging chamber.

        Models 6010A2 and 6024A2 have Post Dilution Water Flow.

OPTIONS:

"J" - Solenoid water control valve.

"K" - Dilution water flow capacity of 60 to 600 GPH ( 230 to 2270 l/h ).

"PS" - Peristaltic Pump.

"S" - Programmable pump ( All pumps except  240 GPD capacity).

"T" - Dilution water flow capacity of 90 to 1200 GPH ( 340 to 4500 l/h ).

CUSTOM OPTIONS can include:

Pump controlled by dilution water flow.  Maintains solution concentration.

HOA switch to allow remote Start - Stop control.

Timer to allow a flush cycle.

Contacts for remote indication of Alarm, Pump Run, Auto Mode.

Low Polymer Flow Alarm.  The switch is a thermal dispersion type, with no moving parts.  Trip point is adjustable.  Minimum flow is 10 GPD.

20 Gallon, or larger, in-line aging tank.

Enclosure to protect the feeder from drips and dust.

Explosion Proof for Class1 Group D installations.

Operating pressure up to 1,500 psi (100 bar).

Other voltages.

Custom instruments to meet your needs.